The use of a multimeter to test the capacitor is a good or bad method.
Capacitors, often referred to simply as capacitors for their ability to hold charge, are denoted by the letter C. Definition 1: A capacitor, as its name implies, is 'a container for electricity', a device that holds an electric charge. English name: capacitor. capacitor is one of the electronic components used in a large number of electronic devices, widely used in circuit isolation through the cross, coupling, bypass, filtering, tuning circuit, energy conversion, control, etc.. Definition 2: Capacitor, any two conductors (including wires) that are insulated from each other and placed very close together constitute a capacitor.
Capacitance is different from capacitor. Capacitance is a fundamental physical quantity with the symbol C and the unit F (farad).
General formula C = Q / U parallel plate capacitor special formula: the electric field strength between the plates E = U/d, capacitor capacitance determinant C = εS/4πkd
With the rapid changes in electronic information technology, digital electronic products are updated more and more quickly to flat-panel TVs (LCD and PDP), notebook computers, digital cameras and other products based on the production and sales of consumer electronics products continue to grow, driving the growth of the capacitor industry. And led to the development of related materials, equipment industry, China has become the world's leading producer of capacitors.
1, the detection of fixed capacitors
A Detection of small capacitors below 10pF
Because the capacity of fixed capacitors below 10PF is too small, measurement with a multimeter can only qualitatively check whether there is leakage, internal short circuit or breakdown phenomenon. Measurement, you can choose the multimeter R × 10k block, with two pens were connected to any two pins of the capacitor, the resistance should be infinity. If the measured resistance (pointer swing to the right) is zero, then the capacitor leakage damage or internal breakdown.
B test 10PF ~ 0 01μF fixed capacitor whether the charging phenomenon, and then judge its good or bad.
Multimeter selection R × 1k block. Two transistor β value are more than 100, and the penetration current should be small. Can choose 3DG6 and other models of silicon transistors to form a composite tube. The red and black pens of the multimeter are connected to the emitter e and collector c of the composite tube. Due to the amplifying effect of the composite transistor, the measured capacitance of the charge and discharge process to be amplified, so that the multimeter pointer swing amplitude increased, thus facilitating observation. It should be noted that: in the test * work, especially in the measurement of smaller capacitance, to repeatedly switch the measured capacitance pin contact A, B two points, in order to clearly see the multimeter pointer swing.
C For fixed capacitors above 0.01μF, the multimeter can be used to directly test the capacitor with or without charging process and internal short-circuit or leakage, and according to the magnitude of the pointer swing to the right to estimate the capacity of the capacitor.
2,Electrolytic capacitor test
A Because the capacity of electrolytic capacitors is much larger than that of general fixed capacitors, therefore, when measuring, the appropriate range should be selected for different capacities. According to experience, in general, 1 ~ 47μF capacitance, available R × 1k block measurement, greater than 47μF capacitance can be R × 100 block measurement.
B will be the multimeter red pen connected to the negative pole, the black pen connected to the positive pole, in just the moment of contact, the multimeter pointer that is to the right of a larger deflection (for the same resistance block, the larger the capacity, the larger the amplitude of the pendulum), and then gradually turn back to the left until it stops at a certain position. At this time the resistance value is the forward leakage resistance of electrolytic capacitors, this value is slightly larger than the reverse leakage resistance. Practical experience shows that the leakage resistance of electrolytic capacitors should generally be more than a few hundred kΩ, otherwise, it will not work properly. In the test, if the positive and reverse are not charging phenomenon, that is, the needle does not move, it means that the capacity disappears or internal disconnection; if the measured resistance is very small or zero, the capacitor leakage or has been damaged by breakdown, can not be used again.
C For positive and negative signs of the electrolytic capacitor is unknown, can be used to measure the leakage resistance of the above method to identify. That is, the first arbitrary measurement of the leakage resistance, remember its size, and then exchange the pen and then measured a resistance value. Two measurements in the resistance value of the larger one is the positive connection, that is, the black pen is connected to the positive terminal, the red pen is connected to the negative terminal.
D use the multimeter resistance block, using the electrolytic capacitor for positive and negative charging method, according to the pointer to the right of the magnitude of the swing, you can estimate the capacity of the electrolytic capacitor.
3,Variable capacitor detection
A gently rotate the shaft by hand, it should feel very smooth, and should not feel sometimes loose and sometimes tight or even stagnant phenomenon. Will carry the shaft forward, back, up, down, left, right and other directions to promote, the shaft should not be loose phenomenon.
B Rotate the spindle with one hand and lightly touch the outer edge of the moving piece set with the other hand, and no looseness should be felt. A variable capacitor with poor contact between the spindle and the moving piece cannot be used further.
C Place the multimeter at R×10k block, connect the two pens to the lead-outs of the movable and fixed pieces of the variable capacitor with one hand, and connect the rotor to the lead-outs of the movable and fixed pieces with the other hand.
end of the variable capacitor, the other hand will slowly rotate the spindle a few times, the multimeter pointer should be at infinity position. In the process of rotating the rotary axis, if the pointer sometimes points to zero, indicating that there is a short-circuit point between the moving piece and the fixed piece; if encountered at a certain angle, the multimeter reading is not infinity, but a certain resistance, indicating that there is a leakage of variable capacitors between the moving piece and the fixed piece.
